How to use beeswax wood polish?

How to use beeswax wood polish?

How to use beeswax wood polish?

As a wood polish and protectant, beeswax isn’t just a buzzword. It works by subtracting the toxins. Beeswax wood varnish products are not a discovery. Once upon a time, all wood products were made of pure beeswax. However, concerns about sustainability and the need to mass-produce wax-free products have led to the emergence of cleaning alternatives that use toxic chemicals. That is how we’ve become accustomed to the toxic smell of regular bathroom cleaners, dishwashing liquids, and floor polishes. Likewise, we got tired of these headache-causing chemicals. We decided to take back control of what type of detergent we used.

Beeswax over traditional wooden polishes

Hardwood furniture, such as oak, teak, shisham, or mango, should regularly be treated with a high-quality finish. Apply at least three to four times a year to keep the wood in top condition. Untreated wood can crack or split easily and stain from moisture or spills. Beeswax is highly recommended. Avoid store-bought abrasive sprays as they are silicone-based and only serve to dry the wood. This article will show you how to apply beeswax to hardwood furniture.

The best type of beeswax polish is natural beeswax cream. Creamy beeswax is easier to work with than hard wax and doesn’t clump like paste polish. Not only does beeswax give your furniture a deep, shiny luster, but it also provides a low-odor, clear varnish. Applying beeswax for polishing is not a difficult or time-consuming operation, but you should do it with care.

Best method to use beeswax wood polish?

Step 1: Thoroughly clean the wood surface  

The main rule is always thoroughly clean the surface before refinishing. However, if the surface is relatively clean and foreign matter is a concern, wash it with warm, soapy water and rub gently. 

Rinse thoroughly and air dry. However, working on an entirely new surface requires removing all old paint, wax, varnish, or other finishes. Scrape off any loose finish and repeat this process if necessary. Finally, thoroughly rinse the surface with a strong wood cleaner along with plenty of water. Wipe off excess water and allow the surface to dry completely. Depending on the weather in your area, this may take 2-3 hours or more if necessary.

Step 2: Sand the surface of the furniture before application

Sand the wood surface with fine sandpaper before waxing. It will make the wood better absorb the wax later on. You work evenly and leave no spots. Only then can you achieve consistent results. A skinny layer remains on the surface of the wood and may not be noticeable, but this prevents the wax from being absorbed into the wood. Therefore, you should sand furniture.

Step 3: Apply the first wood varnish with beeswax 

Once the surface is clean, apply using a clean, lint-free cloth. The trick here is to use a minimal amount, neither too little nor too much of the wax. Remove the wax from the jar with a cloth and apply the wax to the furniture in long, broad strokes along the wood grain. Repeat the same process for the entire surface of the wooden furniture. Make sure the wax layer is light and even.

When applying beeswax to wood, be careful not to use too much or too little beeswax, and work evenly with a soft, lint-free cloth or cloth. Then remove the residues with a rag or rough cloth. Apply wax paste or finishing wax evenly with a fiber cloth. Also, do not apply a thick layer as it can be uneven when drying. On the other hand, adjusting the wrist step in the beta direction avoids unnecessary shadows.

Tip: Beeswax works best at room temperature. But don’t make it too warm. Otherwise, it will not apply evenly everywhere. The wood immediately absorbs the entire wax mass from which the warm wax rises. Of course, stains are unavoidable.

Step 4: Wait for the first coat of wax to dry 

Let the first coat of beeswax furniture polish dry for 15-20 minutes. This time may vary depending on the temperature and humidity of the area and the porosity of the wood. The idea is to give the wood enough time to absorb the wax. This time interval provides a good surface for the next layer to be adhered to without smearing.

Step 5: Apply the coat of beeswax twice 

Reapply another layer of wax in the same way as the first, with light movements smooth, long strokes. Again, use a clean piece of lint-free cloth that you are using. Untreated or untreated wood must be waxed at least three times. Two coats of wax are sufficient for pre-finished wooden surfaces. If your polish is dirty or doesn’t come out as expected, read our tips on removing wax stains.

After waxing, let it dry to the touch. Then repeat this process for third or more layers of wax. Once you have applied all the layers of beeswax you want for your project, allow the final coating to dry completely to prepare it for varnish.

Step 6: Polish the finished wood surface 

Use a clean rag or cloth to wipe the wax surface in circular motions. Polishing removes excess varnish and softens wax build-up in corners and crevices. In the process, the finished product shines. Continue polishing the top, sides, and corners of wooden furniture with a clean cloth. Repeat this process until you are satisfied with the level of the luster of the wooden table.

Switch to beeswax wood varnish and preservative now

With such good reasons to work with beeswax, it’s time for all of us to switch to a greener and healthier way to clean and preserve wood household items. Beeswax is a true gift of nature and a friend of trees. It shouldn’t be just a whim. Let’s make it a lifestyle. Hopefully this article have all the necessary information to fulfill your requirements. LEt me know your feedback in the comment section.